REMOTE  -  TRANSMITTER

TRACER INSIDE

The first radio with TBS Tracer built in. And it fits your existing TBS Crossfire module through the JR bay! TBS Tracer is the world's lowest latency radio link, and builds upon the rock-solid reputation of the TBS Crossfire code base. With the continued development and expansion of the TBS ecosystem, pilots will remain on the bleeding edge of capabilities paired with the ease of use and overall robustness that TBS products are known for.

1.6ms end to end latency

250Hz refresh rate

Long range capable

High telemetry throughput for Mavlink and long range missions

TBS Cloud connectivity

FEATURES

TBS Tracer built-in

CRSF V3 protocol support for lowest latency and most direct response of any remote control available

Range of up to 25km / 15mi

Built-in antenna for ultimate ruggedness

External antenna available as add-on

Full size, ball bearing hall sensor gimbals

Configurable resistance and tension

Adjustable throttle & pitch throw (+/- 10 degrees)

Spare spring set included for lower tension

Ergonomic shell design with grippy rubber edges

4x 3-position switches

2x potentiometer with center notch

1x 2-position switches

1x momentary button

4x digital trim buttons

Perfectly balanced lanyard mount

Up to 12 channels supported

Parallel 18650 x 2 (not included!) with USB-C 2A charging (2.5 hours for full charge)

Speech audio output with audio jack & haptic vibration alert

Open Source remote control operating system (FreedomTX, temporary fork of OpenTX)

Rocker dial and 3 button menu for super simple navigation

High resolution (128*64) black & white LCD screen w/ backlight

100+ model memory with included SD-card

TBS Cloud compatible

SPECIFICATION

Weight: 565g

Battery: 2 x 18650 

Audio: 1W speaker & 3.5mm headphone jack

Display: 3.5” LCD panel (128 x 64)

Antenna: Embedded antenna

Switches: 4 x 3pos | 1 x 2pos | 1 x Momentary

USB-C Port: Battery charging (5V, 1A), Firmware upgrades & Simulator / HID

INCLUDES

1 x Ethix Mambo

1 x Springs Set (Lower Tension)

2 x Throttle limitation screws (with allen key)

1 x Custom CNC Kickstand

1 x TBS Crown Jewels gimbal sticks 

1 x Ethix Sticker Sheet

1 x Ethix Neck Strap V2

MORE INFORMATION

TBS Mambo Manual

FreedomTX source code

Mambo SD Card Contents donwload (For Freedom TX 1.2x)

TBS Cloud - Wifi Firmware

TBS Agent Lite

TRACER INSIDE

The first radio with TBS Tracer built in. And it fits your existing TBS Crossfire module through the JR bay! TBS Tracer is the world's lowest latency radio link, and builds upon the rock-solid reputation of the TBS Crossfire code base. With the continued development and expansion of the TBS ecosystem, pilots will remain on the bleeding edge of capabilities paired with the ease of use and overall robustness that TBS products are known for.

1.6ms end to end latency

250Hz refresh rate

Long range capable

High telemetry throughput for Mavlink and long range missions

TBS Cloud connectivity

FEATURES

TBS Tracer built-in

CRSF V3 protocol support for lowest latency and most direct response of any remote control available

Range of up to 25km / 15mi

Built-in antenna for ultimate ruggedness

External antenna available as add-on

Full size, ball bearing hall sensor gimbals

Configurable resistance and tension

Adjustable throttle & pitch throw (+/- 10 degrees)

Spare spring set included for lower tension

Ergonomic shell design with grippy rubber edges

4x 3-position switches

2x potentiometer with center notch

1x 2-position switches

1x momentary button

4x digital trim buttons

Perfectly balanced lanyard mount

Up to 12 channels supported

Parallel 18650 x 2 (not included!) with USB-C 2A charging (2.5 hours for full charge)

Speech audio output with audio jack & haptic vibration alert

Open Source remote control operating system (FreedomTX, temporary fork of OpenTX)

Rocker dial and 3 button menu for super simple navigation

High resolution (128*64) black & white LCD screen w/ backlight

100+ model memory with included SD-card

TBS Cloud compatible

SPECIFICATION

Weight: 565g

Battery: 2 x 18650 

Audio: 1W speaker & 3.5mm headphone jack

Display: 3.5” LCD panel (128 x 64)

Antenna: Embedded antenna

Switches: 4 x 3pos | 1 x 2pos | 1 x Momentary

USB-C Port: Battery charging (5V, 1A), Firmware upgrades & Simulator / HID

LiteRadio 2 SE ist die aktualisierte Version, die auf der LiteRadio 2 basiert

und enorme Verbesserungen aufweist:der eingebaute 1000 mAh 1S LipoAkku

erhöht die Laufleistung auf mind. 8 Stunden

Updates mit dem von BETAFPV selbst entwickelten LiteRadio-System.

Piloten können die Joystick-Kalibrierungs- und Upgrade-Firmware direkt am Funksender bedienen

diese Version unterstützt Frsky, Piloten können den Futaba S-FHSS, Frsky D8,

Frsky FCC D16 und Frsky LBT D16 Modus (nur ACCST V1), S-FHSS und Frsky

Empfänger ACCST V1 ohne Telemetrierückkanal, einfach über den Funksender wechseln.

mit einer Sendeleistung von 100 mW bietet die LiteRadio 2 SE eine größere Reichweite

die LiteRadio 2 SE verfügt über ein eingebautes Lademodul

und unterstützt das bequemere USB-Laden.

LiteRadio 2 SE ist ergonomisch und hat die Form eines Gaming-Controllers.

Es liegt angenehm in der Hand und die rutschfeste Textur an den Griffen sorgt für einen soliden Griff.

Dieser Funksender fungiert als USB-Joystick, wenn er an einen PC angeschlossen ist.

Sie können es also verwenden, um FPV-Simulatoren zu spielen.

SPECS

Farbe weiß

Frequenzbereich: 2,4 G (2403 MHz - 2447 MHz)

Kanal: 8

Unterstützungsprotokoll: Futaba S-FHSS, Frsky FCC D16 / Frsky LBT D16 / Frsky D8

(im Auslieferungszustand nur ACCST V1)

Leistung: ≤ 100 MW

Unterstützt USB-Aufladung / Firmware-Aktualisierung

Unterstützt BETAFPV Simulator Connected / Customized LiteRadio System / Joystick Calibration

LED-Leuchte: Grün-Einschalten / Rot-Warnung / Blau-Normal

Batterie: Eingebaute 1000mAh 1S Batterie

Ladeanschluss: Typ C

 Built in USB-C Charging.

Touch Panel

USB-C Data/simulator port.

Bigger battery compartment.

External SD card slot.

2 X UART ports for updates and DIY.

Improved menu navigation with Page back and forward.

Better case design with improved grip ergonomics.

Better switch quality and placement design.

Better sliders with good center feedback.

Full Size (not small short throw) HALL gimbal with CNC Aluminum face.

Official OpenTX support.

Official Multi-module support.

Improved speaker circuit (no noise).

Included EPP carry box.

SPECS:

* HAL-Sensor Gimbals in Originalgröße

* Kugellager

Konfigurierbarer Widerstand und Spannung

Einstellbarer Gas- und Pitch-Throw (+/- 10 Grad)

Ersatzfedern für weniger Stickwiderstand enthalten

Faltbare Gimbal Sticks 

* Ergonomisches und kompaktes Design mit bequemen Gummigriffen

* Robuste, optimierte Schalter

2x 2-Positionsschalter

2x 3-Positionsschalter

2x Kurzwahltasten

* TBS Crossfire eingebaut

Schwenkantenne, die gleichzeitig als Ständer dient

Es werden bis zu 12 Kanäle unterstützt

* Eingebauter 5000mAh 1S LiPo mit USB-C 2A-Aufladung (2,5 Stunden für volle Aufladung)

* Sprachausgabe mit Audioanschluss und Vibrationsalarm

* Open Source-Fernsteuerungsbetriebssystem (FreedomTX, temporärer Zweig von OpenTX)

* Wippe und 3-Tasten-Menü für supereinfache Navigation

* Hochauflösender (128 * 96) schwarzweißer OLED-Bildschirm mit Hintergrundbeleuchtung

* Über 100 Modellspeicher mit mitgelieferter SD-Karte

* Mit der TBS Cloud kompatibel

LIEFERUMFANG

1 x Tango 2 Pro

1 x Samttragetasche mit TBS-Logo

1 x Federn Set (Default und Lower Tension)

2 x Wegbegrenzungsschrauben für Gas und Pitch (mit Inbusschlüssel)

1 x Aufkleberbogen

MEHR INFORMATIONEN

SUPPORT

TBS Tango 2 Handbuch

SPECS:

* HAL-Sensor Gimbals in Originalgröße

* Kugellager

Konfigurierbarer Widerstand und Spannung

Einstellbarer Gas- und Pitch-Throw (+/- 10 Grad)

Ersatzfedern für weniger Stickwiderstand enthalten

* Ergonomisches und kompaktes Design mit bequemen Gummigriffen

* Robuste, optimierte Schalter

2x 2-Positionsschalter

2x 3-Positionsschalter

2x Kurzwahltasten

* TBS Crossfire eingebaut

Schwenkantenne, die gleichzeitig als Ständer dient

Es werden bis zu 12 Kanäle unterstützt

* Eingebauter 5000mAh 1S LiPo mit USB-C 2A-Aufladung (2,5 Stunden für volle Aufladung)

* Sprachausgabe mit Audioanschluss und Vibrationsalarm

* Open Source-Fernsteuerungsbetriebssystem (FreedomTX, temporärer Zweig von OpenTX)

* Wippe und 3-Tasten-Menü für supereinfache Navigation

* Hochauflösender (128 * 96) schwarzweißer OLED-Bildschirm mit Hintergrundbeleuchtung

* Über 100 Modellspeicher mit mitgelieferter SD-Karte

* Mit der TBS Cloud kompatibel

LIEFERUMFANG

1 x Tango 2

1 x Samttragetasche mit TBS-Logo

1 x Federn Set (Default und Lower Tension)

2 x Wegbegrenzungsschrauben für Gas und Pitch (mit Inbusschlüssel)

1 x Aufkleberbogen

MEHR INFORMATIONEN

SUPPORT

TBS Tango 2 Handbuch

TBS Multi Protocol Module (MPM) Transmitter Module,

compatible with OpenTX / FreedomTX for TBS Tango 2,

X-Lite and X9 Lite (X9 lite needs adapter, sold separately below!)

The TBS MPM, designed in collaboration with RadioMaster,

features the four main RF chipsets (CC2500, NRF24L01, A7105 and CYRF6936)

all integrated in a single product. Thanks to OpenSource developers,

compatibility with most common R/C protocols

is provided through a single module, powered by OpenTX / FreedomTX.

With an integrated RF amplifier, the module provides competitive range.

SPECS

Input voltage: 6-9v

Current: ~100mA

Operating frequency: 2.4GHz ISM band

RF power: +20DBM (100mW)

Main Chipset: STM32

Opensource Repo: Github

Model compatibility: Alphabetical List (external)

Firmware updatable via USB-C port

INSTALLATION

Install the FPC cable to the PCB.

With the blue side facing up, lift the lock and slide the cable in then lock it down. 

Feed the cable through the bottom and place the PCB to the module bay.  

Turn the module bay around to make sure everything fits accordingly. 

Close the case with the 2 screws provided

Use a dremel, knife or solder tip to cut a small hole accoridng to the outline. 

Slide the flex PCB through the drilled case. 

Clean the back surface and tape the Tango 2 module bay down 

 Install the FPC cable into the receptacle. 

Close the Tango2 case, and you're done!

Warning: The batch 1 of Tango 2 shipped without module bay capability.

Please verify that there is a connector (in pictures above) before purchasing this add-on. 

Also, whenever opening up your Tango 2 in future,

you will need to open the module bay and release the flex PCB from the socket.

SPECS

"LITE" style module bay add-on for Tango 2

Compatiible with TBS Tango 2 mainboard "V006H" and up

The latest revision of the Tango 2 board to bring your existing Tango 2 up to the latest version.

Module Bay Add-on Ready

Micro TX V2 internals

The ultimate stick end for any pilot. Pincher, thumber or hybrid-pinchers

will appreciate several firsts for stick ends:

Wide upper section for thumbers with sharp crowns for maximum grip

Non-symmetrical finger grooves for hybrid pinchers with fingers of various size

Height-adjustable dual pieces that counter-lock

Compatible with all TBS remotes, and other popular radios

Priceless opportunity for dad-jokes included!

 SPECS

Material: CNC Aluminum

Heigh (Total): 20mm

Width (Top): 9.75mm

IN THE BOX

2 x TBS Crown Jewels

INCLUDES

1 x Top Shell

1 x Bottom Shell

2 x Momentary switch Buttons

1 x [Exit Menu Page] Buttons

1 x LED Diffuser  

2 x Case Tags

Antenne ist extra zu bestellen ;)

INCLUDES

1 x Antenna

1 x Rubber Strap

1 x Metal Bracket

2 x Scews

INCLUDES

CNC Aluminum Neck Strap Mount

Flat head M4.0 x 8mm screw

Rubber O-Ring for zero play

By popular demand from our test pilots we offer this mod set

for changing the built-in antenna to an external SMA antenna.

Can also be used to mount SMA extensions for in-car operation.