Zeez F7 Specifications:
Mounting holes: 30×30
Up to 8S input (max 36V)
5V BEC up to 3A continuous
STM32F722 MCU (Support BetaFlight, EmuFlight, INav)
MPU6000 Gyro/ACC for smooth performance
128MB Onboard flash
OSD chip Onboard
6 available UART
VTX switch to control the ON/OFF of the VTX
directly from your transmitter
LC Filter for 5V VTX
USB Type C connector
Onboard RGB LED distribution for clean wiring
to the LED on the arm of the quad.
Onboard RBG LED
Notch design on sides and in the front of the – FC
for better fitting on the frame.
Direct solder connection and board space for TBS Nano RX and TBS Unify Pro32 Nano
Logic Side and USB current protection
Zeez ESC 4in1 60A Specifications:
Mounting holes: 30×30
Input: 3S to 6S
High quality Mosfet: 60A continuous current draw /90A peak current
Aluminum HeatSink to cooldown the Mosfet.
BlHeli32 Firmware (support Dshot150/ Dhsot300 /Dshot600/ProShot 1000)
8 Pin JST connector and 8 Pin solder pads
Holes for Aluminum Low ESR capacitor (included 35V 470uF Low ESR capacitor and a spare capacitor)
Onboard analog current sensor (Firmware Scale: 350)
ESC telemetry to read RPM and ESC temperature
Compatible with Bidirectional Dshot out of the box
Zeez RGB LED strip specifications:
Zeez Led System include 4 strip of RGB led light
10 RBG Led on every strip
Max Current Draw (10 led ON, white color): 0.6A @ 5V
Dimension 35mmx7.5mm (the smallest RBG strip for FPV drone on the market)
Zeez 3030 STACK (with LED) includes:
(1X) Zeez F7 Flight Controller
(1X) Zeez 60A 4in1 ESC
(1X) Zeez Led System (4 led Strip)
(8X) Aluminum Standoff
(4X) Aluminum Nut
(1X) ESC to Flight Controller 8 Pin to 8 Pin JST SH 1.00mm connector
(1X) ESC to Flight Controller 8 Pin to Free wires (with JST SH crimp) JST SH 1.00mm connector
(1X) ESC to Flight Controller 8 Pin to Servo Connector JST SH 1.00mm connector
(1X) JST SH 8 Pin Plastic Housing
(1X) JST SH 10 Pin Plastic Housing
(6X) Led Strip to Flight Controller 3 pin JST SH 1.00mm connector
(2X) 470uF 35V Low ESR Capacitor
(1X) XT60 with 12AWG Silicon Cable for battery connection
(2X) 2.00mm Header Pin for VTX connection
(2X) 2.54mm Header Pin for Receiver connection
(4X) Spare M3 rubber anti vibration for Flight Controller or ESC
88,00 €
inkl. MwSt, versandkostenfrei in bestimmte Länder
Versandkostenfrei in folgende Länder: Österreich Mehr anzeigen Weniger anzeigen
SPECS
Up to 8S input (max 36V)
5V BEC up to 3A continuous
STM32F722 MCU
MPU6000 Gyro/ACC for smooth performace
128MB OnBoard flash
OSD chip Onboard
6 available UARTS
VTX switch to control the ON/OFF of the VTX
directly from your transmitter
LC Filter for 5V VTX
USB Type C connector
Onboard RGB LED distribution for clean wiring
to the LED on the arm of the quad.
Onboard RBG LED
Notch desing on sides and in the front of the – FC
for better fitting on the frame
45,00 €
inkl. MwSt, zzgl. Versandkosten
Versandkostenfrei in folgende Länder: Mehr anzeigen Weniger anzeigen