AIO  FC/ESC


DIATONE MAMBA AIO F722 MK1 35A 6S 8BIT (INTERNAL USB)

 

FC SPECS

MCU: 216MHz STM32F722RET6

GYRO: MPU6000

Barometer: Yes

OSD: Yes

Blackbox: NO

Uarts: 5 Set

ESC Soft: Dshot300/600

Power Led: Yes

LED Controller: BF LED

F.Port: Yes

RSSI: No

Buzz: Yes

Input: 2~6S Lipo (8.4~25.2V)

TVS Protection: Yes

BEC: 5V 2.5A

MOUNTING: 25.5mm,M2

 

ESC SPECS

MAMAB AIO 35A F722MK1 (INTERNAL USB)

INPUT VOLTAGE: 2~6S Lipo (8.4V~25V)

CONTINUE CURRENT: 35A×4

BURST CURRENT: 45A (10S)

Target:BLHeli_S GH30

SOFT: Dshot300/600

 

70,00 €

  • only a few left !
  • 1 - 3 Tage Lieferzeit1

DIATONE MAMBA F411 25A AIO MK2 4S 8BIT (EXTERNAL USB)

 

FC SPECS

MCU: 100MHz STM32F411CEU6

GYRO: MPU6000

Barometer: Yes

OSD: Yes

Blackbox: NO

Uarts: 2 Set

ESC Soft: Dshot300/600

Power Led: Yes

LED Controller: BF LED

F.Port: No

RSSI: Yes

Buzz: Yes

Input: 2~4S Lipo (8.4~16'8V)

BEC: 5V 2A

MOUNTING: 25.5mm,M2

 

ESC SPECS

MAMAB F411 25A AIO MK2 (EXTERNAL USB)

INPUT VOLTAGE: 2~4S Lipo (8.4V~16.8V)

CONTINUE CURRENT: 25A×4

BURST CURRENT: 35A (10S)

Target:BLHeli_S GH30

SOFT: Dshot300/600

 

 

60,00 €

  • sry - sold out! :( but back in stock soon ;)

TBS PODRACER AIO

 

SPECS FC SIDE

Mounting holes: 25.5×25.5 mm / M2 holes

Crossfire/Tracer RX CH1&2 > Uart 2  /  Pro32 Nano VTX > Uart 1 / Uart 1(RX) - unavailable.

Up to 6S input

5V BEC up to 1.2A continuous

STM32F411 MCU (Support BetaFlight, EmuFlight)

MPU6000 Gyro/ACC

OSD chip Onboard (AT7456E)

2 available UART

LC Filter for 5V VTX and Camera

Direct solder connection for TBS Nano RX and TBS Unify Pro32 Nano

Support programmable LED like WS2812 etc

Built-in current sensor

 

SPECS ESC SIDE

Signal support: PWM, Oneshot125, Oneshot42, Multishot, Dshot150, Dshot300, Dshot600

Input voltage: 2S-6S Lipo

Continuous current: 30A

Peak current: 35A

ESC firmware: BLHELI 32

PWM Frequency Range: 24KHz up to 96KHz

 

78,00 €

  • only a few left !
  • 1 - 3 Tage Lieferzeit1

Jhemcu GHF13 F4 AIO 16x16 mm - 13A

 

 

SPECS

Size: 24.2*28.1mm (M3)

Mounting Hole: 16*16mm

Weight: 4.3g

CPU: STM32F411CE (100MHZ) 

MPU: MPU6000 (SPI) 

Firmware: Betaflight MATEKF411.HEX

Built-in Betaflight OSD (AT7456E)

BEC Output(two): 5V, 2.5A

USART: UART1,UART2

Receiver;SBUS,IBUS,DSM2,DSMX ,TBS (UART2)

Blackbox: NO

Built-in Current Sensor

Support WS2812 LED

Buzzer

Input Voltage: 2-4S Lipo

ESC Current: 13A

ESC Firmware: BLHELI_S G-H-30.HEX

Support  PWM, Oneshot42, Oneshot125, Multishot, Dshot150 and Dshot300, Dshot600

 

IN THE BOX

1 x JHEMCU GHF13 AIO F4 FC AIO 13A ESC Board

2 x Power Cable-18AWG

1 x Plug Connector-XT30

1 x Electrolytic capacitor-220UF/25V

 

45,00 €

  • only a few left !
  • 1 - 3 Tage Lieferzeit1

Jhemcu F722 40A BL32 AIO

 

SPECS FC

CPU:STM32F722RE

Sensor:MPU6000(SPI Connection)

OSD: AT7456E

Barometer:BMP280

Black box:16MB

Bluetooth:BL4.0 (NAME:JHEMCU),Configuration UART3

BEC: 5V/2.5A, 10V/2.5A

ESC TX:UART1

HDVTX:DJI VTX->UART6

RC_IN:UART2

UART:UART1,UART2,UART3,UART4,UART5,UART6

USB:TYPE-C

IO2:MODE->USER2 Custom port

Size: 30.5*30.5MM (Max: 42*43MM)

Firmware: JHEF7DUAL

Receiver: SBUS, IBUS, DSM2, DSMX, TBS

Support programmable LED such as WS2812

Support buzzer

Built-in current sensor

Weight: 11.6 grams

 

SPECS ESC

BLHELI_32

Support PWM, Oneshot125, Oneshot42, Multishot, Dshot150, Dshot300, Dshot600, DSHOT1200

Input voltage: 3S-6S Lipo

Continuous current: 40A

Firmware: BLHELI_32 JHE_Aria_32_Multi

 

 

IN THE BOX

1x Jhemcu F722 3-6S AIO 30x30 Flight Controller w/ 40A 32Bit 4in1 ESC

 

74,00 €

  • on stock!
  • 1 - 3 Tage Lieferzeit1

FETtec Mini AIO 15A

 

FEATURES

Full FETtec AIO with KISS FC Firmware

4 ESCs 15A

2-4s

Graphical OSD with full KISS tuning

 

FC

STM32F303CCT6 @ 72MHz

MPU6000

Supply voltage 6-18V (2-4s LiPo)

1x 5V BEC (max 1A)

Dshot 600

 

 

ESC

Active current limiting @ 15A

Input voltage: 2s-4s

High quality 30V MOSFETs

STM32G071 @ 64MHz

128 kHz Motor PWM

Automatic input signal detection

Dshot

PWM

OneShot42/125

 

DIMENSIONS

Size: 29 x 29 mm

Mounting: 25,5 x 25,5 mm

Weight: 3,41 g

 

 

IN THE BOX 

 1x FETtec Mini AIO 15A

1x Capacitor 35V 330µF

 

65,00 €

  • on stock!
  • 1 - 3 Tage Lieferzeit1

BetaFPV Toothpick F722 2-6S AIO - 35A (BLHeli_S)

 

SPECS FC

Item: F722 35A AIO FC(BLHeli_S)

Weight: 7.89g

CPU: STM32F722RET6

Six-Axis: MPU6000 (SPI connection)

Mounting hole size: 26mm * 26mm

Firmware version: betaflight_4.2.x_BETAFPVF722

OSD: Built-in BetaFlight OSD (OSD chip: AT7456E)

Support programmable LED like WS2812 etc

Built-in current sensor

 

SPECS ESC

Signal support: PWM, Oneshot125, Oneshot42, Multishot, Dshot150, Dshot300, Dshot600

Receiver: Support Frsky XM/XM+ Receiver/ Futaba Receiver/Flysky Receiver/DSMX Receiver/

TBS Crossfire Receiver (requires external connection)

Input voltage: 2S-6S Lipo

Continuous current: 35A

Peak current: 40A

ESC firmware: BLHELI_S 32

Indicators: 2 indicators: receiver indicator (green)/Flight control power indicator (red)

Capacitance: CS|5*10*13mm|470μF|35V

Connecter: 80mm 14AWG silicone cable with XT60

Recommended motors: 14XX series, 15XX series, 16XX series, 18XX series, 20XX series

Status LED

There are 2 LEDs on the bottom of the board to indicate the status,

including the Receiver LED ( Green) and FC Power LED ( Red ).

LED  Status  Description

Mode LED (Green)  Solid Horizon Mode/ Angle Mode

Mode LED (Green)  Extinguished Acro Mode

Power LED (Red)  Solid  Power on

 

 

IN THE BOX

1 * Toothpick F722 35A AIO 2-6S brushless flight controller

1 * Cable Pigtail (XT60U)

1 * Capacitance

1 * 6-Pin Connector for DJI Digital VTX

4 * M2x10mm Screws

8 * M2 Nuts

 

80,00 €

  • on stock!
  • 1 - 3 Tage Lieferzeit1

BetaFPV Toothpick F4 2-6S AIO - 35A (BLHeli_32)

 

SPECS  FC

Artikel: F4 35A AIO FC (BLHeli_32)

Gewicht: 7g

CPU: STM32F411CEU6

Sechs-Achsen: MPU6000 (SPI-Verbindung)

Montagelochgröße: 26mm * 26mm

Firmware-Version: BETAFPVF411 (BEFH)

OSD: Eingebautes BetaFlight-OSD (OSD-Chip: AT7456E)

Unterstützt programmierbare LED wie WS2812 usw.

Eingebauter Stromsensor

 

 

SPECS ESC

Signalunterstützung: PWM, Oneshot125, Oneshot42, Multishot, Dshot150, Dshot300, Dshot600

Empfänger: Unterstützung von Frsky XM / XM + Empfänger / Futaba Empfänger / Flysky Empfänger / DSMX Empfänger / TBS Crossfire Empfänger (erfordert externe Verbindung)

Eingangsspannung: 2S-6S Lipo

Dauerstrom: 35A

Spitzenstrom: 40A

ESC-Firmware: BLHELI_S 32

Anzeigen: 3 Anzeigen: Empfängeranzeige (grün) / Flugsteuerungsstatusanzeige (blau) / Flugsteuerungsleistungsanzeige (rot)

Kapazität: CS | 5 * 10 * 17 mm | 680µF | 35V

Anschluss: XT60U 14AWG

 

LIEFERUMFANG

1 * Toothpick F4 35A AIO 2-6S bruchless Flugregler

1 * Kabelpigtail (XT60U)

1 * Kondensaator

4 * M2x10mm Schrauben

8 * M2-Muttern

4 * Schwingungsdämpfende Gummidämpfer

 

72,00 €

  • sry - sold out! :( but back in stock soon ;)

Toothpick F405 2-4S AIO Brushless Flight Controller 20A (BLHELI_32) V4

 

SPECS FC

CPU: STM32F405RGT6

Six-Axis: MPU6000

Size: 26mm x 26mm, whoop mounting pattern

Firmware version: Batefight-BETAFPV405-4.2.X

OSD: Built-in BetaFlight OSD (STM32 controls OSD chip over SPI in DMA mode)

Receiver: Support Frsky XM/XM+ Receiver/ Futaba Receiver/ Flysky Receiver/ TBS Crossfire Receiver/DSMX Receiver

Connecter: XT30, it also can be changed to XT60 if pilots needs.

Weight: 5.76g

 

SPECS ESC

Support PWM, Oneshot125, Oneshot42, Multishot, Dshot150, Dshot300,Dshot600

Input voltage: 2S-4S Lipo

Continuous current: 20A

Peak current: 22A

Firmware: BLHELI-32

 

IN THE BOX

1 * Toothpick F405 20A AIO FC V4

1 * Cable Pigtail (XT30)

4 * M2x10mm screws

4 * M2 nuts 

4 * Anti-vibration rubber dampers

4 * Motor Pluggable Pins

1 * 6-Pin Connector for Digital VTX

1 * 4-Pin Connector for Rx

 

67,00 €

  • on stock!
  • 1 - 3 Tage Lieferzeit1

BetaFPV Toothpick F405 2-4S AIO Brushless Flight Controller 20A (BLHELI_32) V4

 

SPECS FC

CPU: STM32F411CEU6 (100MHZ)

Six-Axis: MPU6000 (SPI connection)

Size: 32.5*32.5mm (26.5mm mounting holes)

Firmware version: Betaflight MATEKF411 (MK41)

OSD: Built-in BetaFlight OSD (OSD chip: AT7456E)

Receiver: Support Frsky XM/XM+ Receiver/

Futaba Receiver/ Flysky Receiver/

TBS Crossfire Receiver/DSMX Receiver

Support programmable LED like WS2812 etc

Built-in current sensor

Weight: 6.63g

 

SPECS ESC

Support BLheli/BLHELI_S suite Pass-through ready

Support PWM, Oneshot125, Oneshot42,

Multishot, Dshot150, Dshot300, Dshot600

Input voltage: 2S-4S Lipo

Continuous current: 20A

Peak current: 25A

Firmware: BLHELI_S

Motor Connectors: 1.25mm header pins connector

 

PACKAGE

1 * Toothpick F4 20A AIO 2-4S brushless flight controller

1 * Cable Pigtail (XT30)

4 * M2x10mm screws

4 * M2 nuts

4 * Anti-vibration rubber dampers

4 * Motor Pluggable Pins

 

60,00 €

  • only a few left !
  • 1 - 3 Tage Lieferzeit1

BETAFPV TOOTHPICK F4 2-4S AIO 12A (BLHELI_S)

 

SPECS FC

CPU: STM32F411CEU6 (100MHZ)

Sechs-Achsen: MPU6000 (SPI-Verbindung)

Größe: 32,5*32,5 mm (26,5 mm Montagelöcher)

Firmware-Version: BetaFlight MATEKF411 (MK41)

OSD: Eingebautes BetaFlight-OSD (OSD-Chip: AT7456E)

Empfänger: Unterstützt Frsky XM/XM+-Empfänger/ Futaba-Empfänger/ Flysky-Empfänger/ TBS Crossfire-Empfänger/DSMX-Empfänger. 

Unterstützt programmierbare LED wie WS2812 usw.

Eingebauter Stromsensor

Gewicht: 6,2g(Ohne Pins), 6,5g(Mit verlöteten Pins)

 

SPECS ESC

Unterstützung der BLheli/BLHELI_S-Suite Pass-through ready

Unterstützt PWM, Oneshot125, Oneshot42, Multishot, Dshot150, Dshot300, Dshot600

Eingangsspannung: 2S-4S Lipo

Kontinuierlicher Strom: 12A

Peak Strom: 15A

Firmware: BLHELI_S

Prozessor: SILABS EFM8BB21F16G-C

Motor-Verbinder: 1,25 mm Header-Pin-Connector

Werksseitige Firmware: G-H-30-16.7

 

Lieferumfang

1 * Toothpick F4 2-4S AIO brushless FC

1 * Kabel mit Stecker (XT30)

4 * M2x10mm Schrauben

4 * M2-Muttern 

4 * Anti-Vibrations-Gummidämpfer

4 * Steckbare Motorstifte (wenn nicht vorverlötet)

 

44,00 €

  • on stock!
  • 1 - 3 Tage Lieferzeit1