AIRBOT  FC


AIRBOT F7

 

STM32 F722 MCU

nur einseitig bestückt für enge,  low profile Builds

ICM20602 Gyro

camera control

direkte LiPo Spannung 3S-6S

5V 2A BEC

6x Hardware UART

Onboard 128Mbit(16MB) flash für balckbox

30.5*30.5 mm Mounting holes

 

49,00 €

  • on stock!
  • 1 - 3 Tage Lieferzeit1

OMNIBUS AIO F4 V6 Flight Control - 5xUARTs

 

Online Guide: https://blog.dronetrest.com/omnibus-f4-v6-flight-controller-guide/

 

OMNIBUS F4's upgrade version, using F405 and new target, with 5x UARTs now.

classic OMNIBUS design, using F4 MCU controls OSD over SPI bus,

compare the first version, we added BMP280 as barometer and SD Card supports.

OSD Configuration has been incl. in Betaflight GUI.

FC incl. 5V1A BEC on board(3-6s) and 1x 8V BEC for Camera

MPU6000 at SPI bus, Ext, SPI for damped gyro

 

Use fireworks v2 firmware, in CLI, set gyro_to_use = SECOND

 

New version with 8PIN Sh1.0 Socket, could be much easier connect to our 4in1 ESC by one cable.

On v5, we added jumpers for Current source select, please read the manual and set the jumper before using the FC.

 

Features:

STM32 F405 MCU, Runs Betaflight 3.0 firmware

SBUS/PPM input (Pinheaders)

6PWM output (1-4Pinheaders and Sh1.0 Plug, 5-6 as Pinheaders)

Only 36x36mm, mount holes 30.5x30.5mm

INCL. BARO BMP280

SPI Sensor MPU6000

Flash

 

Package incl.:

1x FC

 

44,00 €

  • only a few left !
  • 1 - 3 Tage Lieferzeit1

OMNIBUS Fireworks v2

 

The Omnibus Fireworks flight controller uses the ICM20608 over SPI

for the best possible flight performance. With onboard damping box,

the ICM20608 runs perfectly under 32k Gyro loop. If you haven't already seen it,

you should check out Josh's awesome video on different IMUs.

Also onboard are a barometer and AB7456 OSD chip for the BetaFlight integrated OSD.

Omnibus Fireworks supports 3-6s LIPO direct input, build in hall Current Sensor and Power Filter too.

The on Board PDB is tweaked by using 12-Layer PCB design.

There is only 0.2-0.5 mohm internal resistance from input to each output pads

 

Modifications on v2:

Tantalum Capacitors can be added to the board (not included)

Solder pads added for SmartAudio and Camera Control (next to Video pads)

The orientation of IMU FPC optimized

Gyro ribbon cable redesigned to fit without extending outside the board

Added an 8v BEC and LC Filter for the camera and VTX power

This board now has 5 UART ports

 

Features:

STM32 F405 MCU, Runs Betaflight firmware(supported from v3.2)

ICM20608 Over SPI Bus in damping box. (optional MPU6000)

30.5x30.5mm Mounting holes

Supports Lipo direct plugin (3-6S)

Supports 5V 1A BEC output (Buck)

Supports 8V 1A BEC with LC filter output for the camera and VTX(Buck)

STM32 controls OSD chip over SPI in DMA mode (Betaflight OSD)

Built-in hall Current Sensor

Built-in Professional Level PDB

More caps to reduce power noise.

 

Package incl.:

FC/PDB board x 1

 

48,00 €

  • only a few left !
  • 1 - 3 Tage Lieferzeit1

OMNIBUS F4 Nano v6 with LC filter

 

New features on OMNIBUS F4 Nano V6:

 

5x UARTs

Supports ESC Telemetry function on 4in1 Socket

5v 2A BEC

2-6S

 

Firmware, please use Fireworks v2, but 

in CLI, set gyro_to_use = SECOND

 

 

Airbots new V5 brushless AIO flight controller for FPV may be small but is packed with features.

With Support ending for F1 processors, F3 become the bottom wrung,

but don't worry, this little board features an F4 MCU.

Its Betaflight OSD is connected over SPI in DMA, don't know what that means?

It is designed on the current proposed architecture for betaflight,

it will show you any and all data you want on your FPV feed

and you can change settings including tune your PIDs without taking your goggles off!

The board also features an MPU6000 gyro connected over SPI for fast,

accurate, low noise gyro data and can support 2-6s direct input.

 

Notice:

If you plan to use the FC with our 4in1 ESC (Wave or Ori 4in1),

you only need one 8pin Cable (The Option 8pin 4in1 Cable)

 

Features:

- 2-6s direct input (adaptor to connect to Wave 4in1 ESC providing power and ESC signal connection (note Wave is 2-4s))

- MPU6000 gyro connected by SPI for low noise, clean, high frequency gyro samples

- BMP280 Barrometer to enable altitude hold

- Betaflight OSD

- Onboard voltage sensor

- On board 5v regulator, components rated to 2A - recomended 1A max to prevent heat build up)

- built in L-C filter to provide clean power to FPV kit

- STM32 F405 MCU running betaflight 3.2

- pin headers for SBUS/PPM input

- output for 4 motors on JST-SH 1.0 8pin plug connects to Airbot Wave 4in1 ESC

(The Option 8pin 4in1 Cable)

- 25x25mm (20x20mm M3 mount holes)

 

Package:

1x FC

 

30,00 €

  • on stock!
  • 1 - 3 Tage Lieferzeit1

OMNIBUS F4 Nano v7

 

The Omnibus F4 Nano V7 flight controller uses the ICM20602 over SPI

for the stable flight performance.

Also onboard is AB7456 OSD chip for the BetaFlight integrated OSD.

Omnibus F4 Nano V7 using new target,

supports 3-6s LIPO direct input, has 6x Hardware UARTs + 1x I2C

 

Modifications on v7:

Tantalum Capacitors added for noiseless gyro reading

Solder pads added for SmartAudio and Camera Control (next to Video pads)

FPC port for Frsky RX

This board now has 6 UART ports

PWM pads on the corner

5V BEC, 2A output

 

Features:

STM32 F405 MCU, Runs Betaflight firmware

ICM Gyro Over SPI Bus

20 x 20 mm Mounting Holes

Supports Lipo direct plugin (3-6S)

Supports 5V 1A BEC output (Buck)

STM32 controls OSD chip over SPI in DMA mode (Betaflight OSD)

6 UARTs

25x25mm (20x20mm M3 mount holes)

 

Package:

1x FC

 

33,00 €

  • on stock!
  • 1 - 3 Tage Lieferzeit1

8 pin ESC Kabel

1,50 €

  • on stock!
  • 1 - 3 Tage Lieferzeit1